雙組份打膠機的比例調整需根據具體型號和工藝需求進行，以下是關鍵信息整合：

　　The proportion adjustment of the two-component gluing machine needs to be based on specific models and process requirements. The following is the key information integration:

　　基礎比例范圍

　　Basic proportion range

　　GT05雙組份打膠機的標準混合比范圍為 6:1-14:1 ，具體比例需根據實際生產需求調整。

　　The standard mixing ratio range of GT05 two-component gluing machine is 6:1-14:1, and the specific ratio needs to be adjusted according to actual production needs.

　　操作步驟

　　operating steps

　　接通氣源 ：調節供氣壓力至0.4~0.8Mpa，檢查系統密封性，試運行A、B泵及氣缸同步動作。

　　Connect the gas source: Adjust the gas supply pressure to 0.4~0.8Mpa, check the system's sealing, and test run pumps A and B and cylinders synchronously.

　　調整比例 ：通過手動轉閥控制A、B組份膠桶的出膠量，觀察混合效果。若需精細調節，可結合壓力傳感器反饋逐步優化比例。

　　Adjustment ratio: Control the dispensing amount of component A and B from the glue bucket manually by turning the valve, and observe the mixing effect. If fine adjustment is required, the proportion can be gradually optimized by combining pressure sensor feedback.

　　注意事項

　　Precautions

　　比例調整需在系統穩定運行狀態下進行，避免因氣源壓力波動影響混合精度。

　　Proportional adjustment should be carried out in a stable operating state of the system to avoid affecting the mixing accuracy due to fluctuations in gas source pressure.

　　不同行業對比例要求差異較大（如手機點膠常用1:4），建議優先參考產品說明書或咨詢廠家獲取定制化方案。

　　There are significant differences in proportion requirements among different industries (such as 1:4 commonly used for mobile phone dispensing). It is recommended to first refer to the product manual or consult the manufacturer for customized solutions.

　　總結 ：雙組份打膠機比例調整需結合設備參數和實際需求，通過控制氣源壓力和調節膠桶出膠量實現，操作時需注意系統穩定性和比例范圍限制。

　　Summary: The proportion adjustment of the two-component glue machine needs to be combined with equipment parameters and actual needs, achieved by controlling the gas source pressure and adjusting the glue output of the glue bucket. During operation, attention should be paid to system stability and proportion range limitations.

　　本文由 雙組份打膠機  友情奉獻.更多有關的知識請點擊  http://www.hntnauto.com/   真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from a two-component glue machine For more related knowledge, please click http://www.hntnauto.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.