玻璃涂布機的操作流程以下是關鍵步驟和注意事項：

　　The following are the key steps and precautions for operating a glass coating machine:

　　一、開機前準備

　　1、 Preparation before startup

　　1.設備檢查

　　1. Equipment inspection

　　確認氣源壓力正常（如壓縮空氣壓力≥0.5MPa），檢查導輥、軸承、傳動裝置、電機及控制設備是否完好。

　　Confirm that the air source pressure is normal (such as compressed air pressure ≥ 0.5MPa), and check whether the guide rollers, bearings, transmission devices, motors, and control equipment are intact.

　　清潔涂布頭及設備表面，避免殘留物影響涂布效果。

　　Clean the coating head and equipment surface to avoid residue affecting the coating effect.

　　檢查安全防護設施（如踏板、閥門、儀表等）是否正常。

　　Check if the safety protection facilities (such as pedals, valves, instruments, etc.) are functioning properly.

　　2.材料與參數設置

　　2. Material and parameter settings

　　準備符合質量標準的玻璃基材和涂料，確保無污染。

　　Prepare glass substrates and coatings that meet quality standards to ensure no contamination.

　　根據工藝要求預設涂布速度、厚度、溫度（如烘箱預熱至140°C左右）。

　　According to the process requirements, preset the coating speed, thickness, and temperature (such as preheating the oven to around 140 ° C).

　　二、啟動與涂布操作

　　2、 Start up and coating operation

　　1.設備啟動

　　1. Device startup

　　開啟壓縮空氣、循環泵及加熱系統（如油鍋爐需預熱至160°C）。

　　Turn on the compressed air, circulation pump, and heating system (if the oil boiler needs to be preheated to 160 ° C).

　　啟動干燥風機和溫控儀，確認溫度達到工藝要求。

　　Start the drying fan and temperature controller to confirm that the temperature meets the process requirements.

　　2.基材處理

　　2. Substrate treatment

　　將玻璃基材平穩放置于放卷裝置，調整張力防止跑偏或起皺。

　　Place the glass substrate steadily on the unwinding device, adjust the tension to prevent deviation or wrinkling.

　　引紙時保持低速（如20米/分鐘），由專人指揮操作。

　　When guiding the paper, maintain a low speed (such as 20 meters per minute) and have a dedicated person command the operation.

　　3.涂布過程

　　3. Coating process

　　啟動涂布頭，監控涂料流量和涂層均勻性，及時調整參數。

　　Activate the coating head, monitor the flow rate and uniformity of the coating, and adjust parameters in a timely manner.

　　開啟氣刀或刮刀裝置，確保涂布厚度符合設計標準。

　　Turn on the air knife or scraper device to ensure that the coating thickness meets the design standards.

　　三、干燥與收卷

　　3、 Drying and winding

　　1.干燥固化

　　1. Drying and curing

　　涂布后的基材進入烘箱或干燥系統，溫度需逐步降低至60°C以下再關閉。

　　After coating, the substrate enters the oven or drying system, and the temperature needs to be gradually reduced to below 60 ° C before closing.

　　2.收卷與檢測

　　2. Roll up and testing

　　調整收卷張力，避免基材松弛或變形。

　　Adjust the winding tension to avoid substrate relaxation or deformation.

　　每批次完成后取樣檢測涂層質量（如附著力、厚度誤差≤1mm）。

　　After each batch is completed, sample and test the coating quality (such as adhesion and thickness error ≤ 1mm).

　　四、關機與維護

　　4、 Shutdown and maintenance

　　1.停機步驟

　　1. Shutdown steps

　　關閉加熱系統，待溫度降至安全范圍后停止風機和壓縮空氣。

　　Turn off the heating system and stop the fan and compressed air after the temperature drops to a safe range.

　　徹底清潔涂布頭、刮刀等部件，防止涂料殘留。

　　Thoroughly clean the coating head, scraper, and other components to prevent paint residue.

　　2.日常維護

　　2. Daily maintenance

　　定期潤滑氣缸、滑軌等運動部件，檢查螺栓緊固情況。

　　Regularly lubricate moving parts such as cylinders and slides, and check the tightening of bolts.

　　注意事項

　　Precautions

　　安全防護：操作時需佩戴防護用具，避免高溫或機械傷害。

　　Safety protection: Wear protective equipment during operation to avoid high temperatures or mechanical injuries.

　　參數調整：根據玻璃基材特性（如熱膨脹系數）靈活調整涂布速度和溫度。

　　Parameter adjustment: Flexibly adjust the coating speed and temperature based on the characteristics of the glass substrate, such as thermal expansion coefficient.

　　如需更詳細的參數設置或特定機型操作說明，可參考上述來源中的具體流程。

　　For more detailed parameter settings or specific model operation instructions, please refer to the specific process in the above sources.

　　本文由  玻璃涂布機設備   友情奉獻.更多有關的知識請點擊  http://www.hntnauto.com/   真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from glass coating machine equipment For more related knowledge, please click http://www.hntnauto.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.